我第一次玩首辦....有好多問題....
我個隻係 gp01fb 改件 ~

d首辦同副mg gp01 好唔match,一係就砌唔實,點算好 ~? 睇好多post都話用銅枝 ~ so

1. 我應該要買d咩 ~ for example 電鑽 ?銅枝 ?...etc ~
2. HOW much of them ?
3. 最大大大大大問題....點樣攪d銅枝 ? eg, 點樣鑽 ? ~

請各路高人指點 ~~~~
one more....砌首辦有咩係要特別注意 ?

i have not try 首辦, but I can only answer the last question u asked~~

You MUST CLEAN THE PARTS, because when 首辦 produced~they have a coating of chemical on top, so u must clean the parts before u do anything

sry, I don't know how to answer the rest of the questions

example ....1/144 SCALE RESIN CAST KIT
AMX-004
QUBELEY
∼製作風景∼

http://www.traffic-alone.com/

點解你會覺得改件d件會砌得實? 會好match?? 手辦係人手做既, 個矽膠模又係人手做既, 倒模都係人手做既..全部step都係人手整, 冇mg d位咁靚係自然不過既事..

點算..玩改件就要預d件係痴死係個骨上面, 一定要補夾口. 用銅枝係幫助力度, 因為有d件本身有一定重量, 就咁用aa痴都會唔夠實, 用d銅枝"串"住兩件件時重量就可以由銅枝承受..銅枝係唔會令d件更match或更實...

銅枝幼既(1~1.5mm)可以用手自己鑽, 初玩d位會準好多..鑽咀好多模型鋪都有, 我唔幫人賣廣告了..
幾$$?? 鑽咀幾蚊一枝, 建設買多一兩枝, 會斷既...
銅枝就1m十零廿蚊.
點樣鑽?? 呢樣野最好就係"看圖識字"了...

哦..唔該大家 ~...仲有 ~~~如果用手鑽 ~~~會唔會好難的 ????同埋鑽完係咪應該有個"洞",通常用咩整走佢 ~

手鑽唔係/駛要用手指夾住枝鑽咀, 有個 tool, $20~30度

鑽時唔係由"外面"鑽入"內面", 通常係"內面"鑽出"外面"同唔好鑽穿..件與件要量度個位要準..兩件件都係內面鑽...有時有d位好難對準時都會由外面鑽穿一件再鑽入後面果件.  
如果真係鑽穿左就當係夾口咁補就ok...手辦補夾口盡量用原子灰  or 造型畢地補, or aa加爽身粉, 牙膏畢地好多時會唔o岩用..

[ 本帖最後由 vampirea 於 2007-2-28 01:41 PM 編輯 ]

好簡易係圖示...只係其中一方法..中間用既step係冇完全show出來..
http://www.workshop-cast.co.jp/cast_howto.html