第一次玩3D 打印改件, 可以重現一些沒有見過的角色，很有趣!

但打磨功夫很多，而且真的很脆，掉在地上基本上一定爛。

[attach]518469[/attach]

[attach]518470[/attach]

[attach]518471[/attach]

[attach]518472[/attach]

[attach]518473[/attach]

[attach]518474[/attach]

[attach]518475[/attach]

[attach]518476[/attach]

[attach]518477[/attach]

[ 本帖最後由 rubmagician 於 2025-1-22 04:20 PM 編輯 ]

未見過呢款MSV, 有趣!
上色靚!

nice color scheme (blue+pale blue) & weathering.

yes, 3d print is 脆, easy to break, not good for sand (if tiny piece).
yours is addon parts, if print whole model kit, the fitness of different components also a problem. e.g.



[ 本帖最後由 ygat 於 2025-1-22 05:30 PM 編輯 ]

未見過這機設，上色靚，師兄佳作

原來3D件咁脆，如果我淘買的話，要小心一點。

3D件可以說無敵，將來配合埋AI，可能打字都打到隻高達或囡囡出來，唯一問題係再提升打印機解象度。

淘買 has additional problems,
you won't know that shop uses what level of printer (2K, 4K, 8K,...) & material.
also, it may mails you parts that haven't dry (i.e. sticky), or full of defects (contour lines, level difference), etc.

[ 本帖最後由 ygat 於 2025-1-22 11:56 PM 編輯 ]

我不知不覺都買左10套左右，分別由5,6個賣家買, 有本地, 有國內。

其實睇產品相都大約可以判斷到D紋會否好嚴重，有D真係唔敢買, 而價格都好參差，始終係一分錢一分貨。但我又唔想買太貴的，所以都是揀$100港幣左右的，質素已經很不錯。

而未乾透的情況我都遇過，照一陣UV燈就可以了。

只要當是GK改件就無問題了，再加上呢個盟的大家都有豐富砌舊模的經驗，相信沒有大問題的。

the shop i visit only provide 3d rendering.
照燈, thx info. i shall buy a UV lamp.

pm yours shop list for my reference.

腳底噴油地唔地獄？

唔地獄呀, 用刷金邊的方法去上色, 遮蓋根本遮唔到咁仔細

我喺TB買過幾次都遇到ching講既情況,所以唔會再買.最慘有啲無良商人將3D打印件當GK件賣,翻件前又無處理好啲打印紋

我呢套算出得好, 但都有好多打印紋，要用600號沙紙全隻打磨，仲要用水磨, 因為D粉好幼好易吸入，所以都幾攰。

[attach]518491[/attach]


[ 本帖最後由 rubmagician 於 2025-1-24 04:01 PM 編輯 ]

如果這個已經係8K打印，咁就有點失望，距離無需打磨還要等一段時間。

the shop i visit at least won't have this contour lines issues. but price >100, and not gunpla parts.

其實淘寶有很多很多 高達的改件, 只要尋找 "3D打印改件"就得，多到你睇唔晒

我買到既就係下圖咁樣,真係唔知點搞...
[attach]518492[/attach]
[attach]518493[/attach]

我覺得但凡大過1比20既figure都靠唔住,圖就誇啦啦,實物就小喇叭,同詐騙無分別

yes, TB has many 3d print shops, but 90% sell same products.
and i not looking for 高達改件, i want small scale figures.
high 复购% maybe a good reference to believe that shop.




if likes this (contour lines), i will throw immediately.
btw, what scale what character, & how much?
fyr, i request the shop to print in 1/12 (in $200), almost no contour lines, but some parts hasn't dry when arrived, some narrow parts broken, and large gaps + not fit the base (so one foot raised ), etc.



     

[ 本帖最後由 ygat 於 2025-1-25 11:47 PM 編輯 ]

嘩，呢個差得好嚴重 真心攪唔到

我果D又未去到咁

why u do not buy the gk update parts??