the box
test fitting the kit with the iwsp pack
overall every thing looks good
strike rouge before and after
before
after
yup .... i used noir to replace most part of the strike rouge ..... reason :
- strike and noir is very similar
- mobility is way far better then the strike rouge
- proportion wise also better
some action pose to show the mobility
with iwsp pack
head
swap the heal helmet with noir ..... cause i find it strike rouge head is quiet big and ugly .... since the antenna of strike rouge dosent fit noir's helmet so thinking of super glue it when finish or if i come out with other idea
arm
right arm is strike rouge's arm follow by noir's then the end result
at 1st when bashing rouge and noir arm together found out there is a huge problem which is the arm cant be bend at all ...... so had a few surgery
here is where i cut away the parts which is blocking the elbow to bend
the result
leg
cut out some of the pieces to make it same as rouge
the kneed part is the biggest diff here between noir and rouge.... so i saw out the rouge kneed out and place it to noir's leg and also add a little bit of plaplate and bondite to reshape it
the whole leg done
compare
left 1 is noir, meddle is rouge, right is the end result
also i cut out some pieces at the back of the kneed for better 非正版ng
lower body
done reshaping on both leg .......
cover up the internal of the skirt with bondite
sanded the sharp thing to flat
arm
cover up the hole with bondite
remove the top area around the wrist
sb a small part around 2 mm hight with pla plate
place the small part in to the area of the wrist which is remove
end result .... this purpose is to hide the ugly stick like part on the hand
body
cut away the top part ..... btw this part is the fin like thing front of the body
cover the top chest gap with bondite
result
use micro saw to saw away the side front part of the chest .... about 1 mm
replace the area with 1 mm pla plate...
well this part here is not in the original strike rouge design .... just that wanted to added in of a try
test fit .... how dose it look ???
head
lengthen the chick armor and cover up the hole at the fort head with pla plate .... u guys might notice there is still some hole at the fort head after it is been cover up .... this small hole is for the antenna .... as i mention at earlier post the join of rouge antenna and the join of noir helmet is diff so i was to force to remove the join .... at 1st i plan to just glue the part togather but then i scare the glue might spoil the paint after abing so change to this method ...
reshape and sharpen the antenna .... place some brass rod as the join
result
current overall view
shoulder
because of carelessness and sudden loss of concentration i've spoiled the noir shoulder ..... the hole that was drill came out really bad so have to replace with another shoulder
with no more spare noir kit around i was force to use back rouge's shoulder
and this the final result ....
elbow joint
added some detailing
hand
from strike rouge hand with beam saber on it .... i cut out the beam saber and left just the hand
iwsp pack top
the original machine gun on the shoulder was to big .... making the shoulder joint cant move at all ..... to i've make it slimmer
side skirt
added some detail at the top
body
added a piece of pla plate on the top chest
added some mobility mob at the waist
this part is the inner piece of the waist to prevent the inside being expose sb from pla plate 3 mm thick
i added 2 mm pla plate at the waist joint there
add 2 mm pla plate around as a cover also i've cut off some parts for able the body band front and back
result
to show how much it could bend
the usage of the inner block
current over all
arm
sanded down the lower arm to make it slimmer ..... since the whole arm look abit fat
waist
added some detail at the front, back, and side
iwsp pack
didt do much at the pack just some reshaping .....
the left is the mod and right is the original ..... just thin down the mouth of the gun tip .....
left is the mod and right is the original ...... just slim down the side and thin down the back
i readjust the main wing so it look something like a V shape
finish abing surfacer for checking minor error ..... here is the current overall pic
well thats all for now .... the color scheme will be main in orange
still need to clean up some part with hand paint
here is some sneak preview of the kit
[
本帖最後由 zero1st 於 2007-5-23 11:27 PM 編輯 ]
分享
