================
下面 9 樓 update 咗少少嘢
================

對呢隻嘢嘅感想 -->

無言...去相.  多謝參觀.

[attach]400743[/attach]

[attach]400744[/attach]

[attach]400745[/attach]

[attach]400746[/attach]

[attach]400747[/attach]

[attach]400748[/attach]

[attach]400749[/attach]

[attach]400750[/attach]

[attach]400751[/attach]

[attach]400752[/attach]

[attach]400753[/attach]

[attach]400754[/attach]

[attach]400755[/attach]

[attach]400756[/attach]

[attach]400757[/attach]

[ 本帖最後由 abcd2345 於 2012-9-12 03:54 AM 編輯 ]

有无制作过程图呀，好靓呀，~

唔好意思, 冇...

请问电源收藏于那里？我都在整这只，这套件实在 ，考类紧装吾装灯。

呢隻野係個頭樣衰d, 其他都同首辦o個隻有得比, 師兄好手藝

好靚仔啊!
我想知用幾多VOLT 推、電路圖和電阻大少......... THANKS

嘩, 最尾果張好正, 馬沙戰場之魂爆發

一次過 Thanks 各位!!

我用行 12V 用兩粒 12V N 電.  細細粒, 但係留意同 size 有隻係 1.5V!! 唔好買錯.  夠哂位放喺條尾裡面.

不過我諗要用夠 3 粒.  而家腰同腳啲燈唔係好光.

事實上我係用最多 3 粒燈+大電阻行 serial.  所以其實係 9V 到 12V 都得.

電路圖而家就冇囉...

[ 本帖最後由 abcd2345 於 2012-9-11 05:23 PM 編輯 ]

[Update 11/09: 以下雙語廣播 ]

回 高昂 & TDX:

This is the 電阻 I used.  Because I use this bigger 電阻, at maximum 12V, I can connect 1 to 4 LEDs(@3V) in one serial circuit.
[attach]401058[/attach]

And in this kit, each serial circuit (an illustration to follow) I only have 3 LEDs, therefore, I can run either 9V or 12V batteris without problems.  Very flexible, but the draw back is using this 電阻 waste energy... which is probably why I need 3x12V batteries.  

This is where I hide the batteries.  As I said before, I end up using 3 12V batteries...
[attach]401059[/attach]

In terms of wiring, I cut these pieces along the red line to make wiring easier.
[attach]401060[/attach]

This is how I grouped the LEDs.  Each serial circuit must has a separate 電阻.  Every serial circuit is then connected into one parallel circuit.
[attach]401061[/attach]
[attach]401062[/attach]

This is how I cover up the wire
[attach]401063[/attach]

And previous pictures have not shown these LEDs...just for record
[attach]401064[/attach]

之前冇影底 work in progress, 所以就咁分享吓.

[ 本帖最後由 abcd2345 於 2012-9-11 05:25 PM 編輯 ]