改件出現阻滯，腰部balljoint一大一小，合唔到...可能係漏左d野/要用balljoint改一改...
又飛邊又磨面...邊做得咁多野呀

你指嘅 "腰部balljoint" 係改件果 D PARTS? 還是模型果 D PARTS?
要靚就要用心機同時間換取, 遲D你就身同感受

腰部balljoint剛好係首辦件同原件一樣一半....首辦個凹大左，原件個凸細左...搞到依家唔知點算好....
唔通搞到佢幾硬直?我唔制呀~
就算搵ball joint改改佢我都要搞掂佢

梗係改番好佢, 我估你可以切咗模型原本凹果個balljoin落嚟, 痴番上手辦件上.(加銅支, AA膠....)

你係咩砌緊 nz-666呀.. 你預佢硬直吧喇. 冇謂搞咁多野了. 一個唔該搞得唔好會企唔到架.

DANDAN 兄砌緊1:144 HI NU.

1:144 咁既話, 用ab畢地喇. 凹果面先塗凡士林, 凸果面用ab畢地包住個ball joint..壓實之後轉兩轉之後等硬就ok...

一係成個joint轉做關節技.

係nu唔係hi-nu,......

我諗緊幾個方法。
一就係用原件改落去，一定fit
二就係加大個原件粒ball，好似vampire兄咁講。
三就係兩邊一齊改用壽屋關節技...
我已經pm左暗花，唔知係咪份說明書無講/我走漏眼。如果係無既我就試改。
反正要改唔係唔識...

你想唔想知點解會凹果邊大凸果邊細??? 倒cast係一定會縮既. 一縮既自然凹果個凹位變大,凸果邊咪會縮細lor. 唔fit係正常既, 只係幾唔fit姐

o....唔fit到好似一個22吋腰既人著條32吋腰既褲lor....
咁我諗要改改la...

乜方法都好, 祝你成功

Damn everything is to nice!!
But there is still one thing i dont understand,
Maybe you can help me ask people that knows motorcycle well for me
The place where you have the "water tank" seems kind of weird.
As far as i know, the way how a water tank designed, was to set at the front of the vehicle,
so it can catch the incoming cold air and provide the cooling purposes
If it's set after the engine, then the water tank will not be able to have a chance to get cool
sorry if i said too much, but i just wanted to make sure was I right or wrong

原來原件係一粒pc-5既軟膠連接。但大左少少，所以要磨件首辦凹位(磨大佢....)
磨左我成粒幾鐘....勉強入到，但入落去又入唔盡，懷疑係未夠大搞到入唔晒，所以磨磨原件個ball...又係打磨地獄
仲差小腿同腳掌未set...

Thank you for your kind attention on my model.
Yes, your concept is correct. the water tank should be at the front of engine.
My model is also set it at the front of engine. you can refer it at the below picture.
If you have any question, please don't hestitate to contact me.

快d set 起佢 post 嚟睇睇, 最好上埋灰

上完灰就係現形記...
都未搞小腿，希望聽日fullday可以搞多d la~
呢兩日儘量打磨，咁下個禮拜六日開始可以上色XD^^

set好左d首辦件la，但腳部balljoint又出現同一個問題....
依家要加大粒ball
但係手頭上無凡士林@O@
唯有來個純hand make la>~<

O I am really sorry, Sorry for not being familiar enough of the model
I kept thinking that the legs have wheels, didnt think that the other wheel is right behind the seat.
So are you going to have some kind of opening in the front to show that water tank?
will it cause  a bad change of image when it become a robot?

生油都可以